Question 1

When are two exits required from a floor area in Ontario?

Accepted Answer

Under OBC Division B Section 3.4, most floor areas in Part 3 buildings must be served by at least two separate exits. Limited exceptions allow a single exit for small, low-occupancy floor areas. Source: OBC Division B, Sentence 3.4.2.1.(1).

Question 2

When does a building need to be barrier-free (accessible) in Ontario?

Accepted Answer

OBC Section 3.8 requires most buildings other than houses to provide a barrier-free path of travel from the entrance through the principal floor areas. Houses and some small or industrial buildings are exempt. Source: OBC Division B, Section 3.8 (Barrier-Free Design).

Question 3

What fire separation is required between suites in Ontario?

Accepted Answer

In Part 3 buildings, suites must be separated from adjacent suites by a fire separation with a fire-resistance rating, commonly 1 hour, determined by the building's construction requirements in Subsection 3.2.2. Source: OBC Division B, Article 3.3.1.1..

Question 4

What loads must a guard (railing) resist under the Ontario Building Code?

Accepted Answer

Part 4 requires guards to resist specified horizontal and concentrated loads — for example, a horizontal load applied at the top of the guard and loads on individual elements — with values set out in Table 4.1.5.14. Source: OBC Division B, Article 4.1.5.14. and Table 4.1.5.14..

Question 5

How is the design snow load calculated in Ontario?

Accepted Answer

Part 4 calculates roof snow load with the formula S = Is[Ss(Cb Cw Cs Ca) + Sr], using the ground snow load (Ss) and rain load (Sr) for the building's location and factors for roof shape, wind exposure, slope and accumulation. Source: OBC Division B, Article 4.1.6.2..

Question 6

What live loads must residential floors be designed for in Ontario?

Accepted Answer

Table 4.1.5.3. sets residential floor live loads: sleeping and living quarters in dwellings are designed for 1.9 kPa (about 40 psf), with higher loads for exits, corridors and assembly areas. Source: OBC Division B, Article 4.1.5.3. and Table 4.1.5.3..

Question 7

Where is a vapour barrier required in Ontario?

Accepted Answer

Thermally insulated wall, ceiling and floor assemblies must include a vapour barrier to resist moisture diffusing from the warm interior into the assembly. It is installed on the warm side of the insulation. Source: OBC Division B, Subsection 5.5.1. (and 9.25.4. for houses).

Question 8

What are the air barrier requirements in the Ontario Building Code?

Accepted Answer

Assemblies separating conditioned space from the exterior or unconditioned space must include a continuous air barrier system to resist air leakage in both directions. Source: OBC Division B, Subsection 5.4.1. (and 9.25.3. for houses).

Question 9

What performance standards do windows have to meet in Ontario?

Accepted Answer

Windows, doors and skylights must conform to the North American Fenestration Standard, AAMA/WDMA/CSA 101/I.S.2/A440 (NAFS), and the Canadian Supplement CSA A440S1, with performance grades matched to the site's wind and rain exposure. Source: OBC Division B, Subsection 5.10.2. (and 9.7. for houses).

Question 10

What are the ventilation requirements for buildings in Ontario?

Accepted Answer

Part 6 requires buildings to be ventilated by natural or mechanical means, with mechanical ventilation systems designed, constructed and installed to the rates and methods of ASHRAE 62.1. Source: OBC Division B, Section 6.2 (Ventilation).

Question 11

Where can exhaust ducts and vents discharge in Ontario?

Accepted Answer

Exhaust ducts must discharge directly outdoors, located so exhaust air cannot re-enter the building through air intakes, windows or doors, and so it does not create a hazard or nuisance. Source: OBC Division B, Section 6.2 (and 9.32./9.33. for houses).

Question 12

Is an HRV required in new homes in Ontario?

Accepted Answer

New Ontario houses need a principal mechanical ventilation system under Section 9.32, and in practice nearly all SB-12 energy compliance packages require a heat recovery ventilator (HRV) with a specified minimum efficiency. Source: OBC Division B, Section 9.32 and Supplementary Standard SB-12.

Question 13

Is a backwater valve required in Ontario?

Accepted Answer

Where a building drain or branch could be subject to backflow from the public sewer — generally where fixtures are below the level of the adjoining street — the OBC requires protection by a backwater valve. Source: OBC Division B, Article 7.4.6.4..

Question 14

Does every plumbing fixture need a trap in Ontario?

Accepted Answer

Every fixture must be protected by a trap that provides a liquid seal between the drainage system and the room, and every trap seal must be protected by venting so it cannot be siphoned dry. Source: OBC Division B, Section 7.4 (Traps) and Section 7.5 (Venting).

Question 15

What is the maximum hot water temperature allowed in Ontario?

Accepted Answer

Hot water supplied to fixtures in a residential occupancy must not exceed 49°C, with exceptions for dishwashers and clothes washers. Showers additionally require pressure-balanced or thermostatic mixing valves. Source: OBC Division B, Article 7.6.5.1..

Question 16

When does Part 8 (septic systems) of the Ontario Building Code apply?

Accepted Answer

Part 8 governs on-site sewage systems with a design capacity of 10,000 litres per day or less serving a single lot. Installing, altering or repairing one requires a permit from the local principal authority. Source: OBC Division B, Part 8 (Sewage Systems).

Question 17

How far must a septic system be from a well or house in Ontario?

Accepted Answer

Part 8 prescribes minimum horizontal clearances: a leaching bed must generally be at least 15 m from a drilled well (30 m from other wells), 5 m from a structure, 3 m from a property line and 15 m from surface water; septic tanks have shorter setbacks. Source: OBC Division B, Subsection 8.2.1. (clearance tables).

Question 18

How is a septic tank sized in Ontario?

Accepted Answer

A septic tank's working capacity must be at least twice the daily design sanitary sewage flow, and for a residential occupancy not less than 3,600 litres. Design flow is calculated from bedroom count and finished floor area. Source: OBC Division B, Article 8.6.2.2. (tank sizing) and Table 8.2.1.3. (design flows).

Question 19

What is the minimum bedroom size in Ontario?

Accepted Answer

Under the OBC, a bedroom (other than a master bedroom) must be at least 7 m² — reduced to 6 m² where a built-in closet is provided. Master bedrooms require 9.8 m², or 8.8 m² with a built-in closet. Source: OBC Division B, Subsection 9.5.8. (Bedrooms — spaces in dwelling units).

Question 20

What is the minimum ceiling height in Ontario?

Accepted Answer

Rooms in dwelling units generally require a ceiling height of at least 2.3 m over the required floor area, with lower allowances for basements and under beams. Rooms with sloped ceilings can use a portion of the room at full height. Source: OBC Division B, Subsection 9.5.3. (Ceiling Heights) and Table 9.5.3.1..

Question 21

What size does a bedroom egress window need to be in Ontario?

Accepted Answer

Unless the bedroom has a door to the exterior or the dwelling is sprinklered, each bedroom needs a window openable from the inside without tools, providing an unobstructed opening of at least 0.35 m² with no dimension less than 380 mm. Source: OBC Division B, Subsection 9.9.10. (Egress Windows or Doors for Bedrooms).

Question 22

What fire separation does a basement apartment need in Ontario?

Accepted Answer

A second unit must be separated from the rest of the house by a fire separation — generally 45 minutes in new construction, with a reduced rating permitted in existing houses where interconnected smoke alarms are installed. Source: OBC Division B, 9.10.9. (fire separations) and Part 11 / second-unit provisions for existing houses.

Question 23

Which buildings fall under Part 3 of the Ontario Building Code?

Accepted Answer

Part 3 applies to buildings exceeding 600 m2 in building area or three storeys in building height, and to all buildings containing Group A (assembly), Group B (care or detention) or Group F Division 1 (high-hazard industrial) major occupancies. Source: OBC Division A, Subsection 1.1.2..

Question 24

How is major occupancy classified under the Ontario Building Code?

Accepted Answer

Every building or part of a building is classified into a major occupancy group, from Group A (assembly) through Group G (agricultural), based on its principal use. Classification drives construction type, fire protection and egress requirements. Source: OBC Division B, Subsection 3.1.2..

Question 25

How are building height and building area determined under the Ontario Building Code?

Accepted Answer

Building height is the number of storeys between the first storey and the roof, with the first storey established relative to grade. Building area is the greatest horizontal area above grade within exterior walls, measured per storey. Source: OBC Division A, Article 1.4.1.2..

Question 26

What is a high building under the Ontario Building Code?

Accepted Answer

A building is treated as a high building when its top storey floor is more than 36 m above grade for Group A, D, E or F occupancies, or more than 18 m for Group B or C, triggering the additional measures in Subsection 3.2.6. Source: OBC Division B, Article 3.2.6.1..

Question 27

What are the requirements for mixed occupancy buildings in Ontario?

Accepted Answer

Where a building contains more than one major occupancy, each part must meet the rules for its own occupancy, the most restrictive construction requirements often govern, and major occupancies must be separated by rated fire separations per Table 3.1.3.1. Source: OBC Division B, Subsection 3.1.3..

Question 28

When is noncombustible construction required under the Ontario Building Code?

Accepted Answer

The construction articles in Subsection 3.2.2 set permitted construction by occupancy, building height, building area, sprinklering and streets faced. Larger and taller buildings must be noncombustible, while smaller ones may use combustible or encapsulated mass timber construction. Source: OBC Division B, Subsection 3.2.2..

Question 29

When are automatic sprinklers required in a building in Ontario?

Accepted Answer

Sprinklers are required by the applicable 3.2.2 construction article for many occupancies and sizes, and Ontario requires sprinkler protection throughout most new residential buildings more than three storeys, as well as care occupancies and retirement homes. Source: OBC Division B, Subsection 3.2.2..

Question 30

What are the fire department access route requirements under the Ontario Building Code?

Accepted Answer

Buildings must be served by a street or an access route designed for fire department vehicles, located to bring firefighters close to the principal entrance and to hydrants, with clear width, overhead clearance, gradient and load capacity suitable for fire apparatus. Source: OBC Division B, Subsection 3.2.5..

Question 31

When is a fire alarm system required in a building in Ontario?

Accepted Answer

A fire alarm system is generally required in buildings more than three storeys, buildings with an occupant load over 300, buildings with sleeping accommodation for more than 10 people, and in sprinklered buildings, among other triggers. Source: OBC Division B, Subsection 3.2.4..

Question 32

How does spatial separation limit windows near property lines in Ontario?

Accepted Answer

The area of unprotected openings, mainly windows and doors, in an exterior wall is capped based on limiting distance to the property line, wall area and occupancy, and the wall itself may need a fire-resistance rating and noncombustible cladding. Source: OBC Division B, Subsection 3.2.3..

Question 33

When is a standpipe system required under the Ontario Building Code?

Accepted Answer

A standpipe and hose system is generally required in buildings more than three storeys in building height, buildings more than 14 m high measured to the roof, and certain larger low buildings that are not sprinklered throughout. Source: OBC Division B, Subsection 3.2.9..

Question 34

What is the minimum corridor width under the Ontario Building Code?

Accepted Answer

Public corridors must be at least 1 100 mm (about 43 in) wide, with wider minimums for some uses such as care and treatment occupancies, and the width must also satisfy the occupant load calculation of 6.1 mm per person. Source: OBC Division B, Article 3.3.1.9..

Question 35

How long can a dead-end corridor be under the Ontario Building Code?

Accepted Answer

A dead-end public corridor is generally limited to 6 m (about 20 ft), because occupants trapped past the last cross-corridor or exit must be able to retreat quickly. Longer dead ends require redesign or a second egress route. Source: OBC Division B, Article 3.3.1.9..

Question 36

How do you calculate occupant load under the Ontario Building Code?

Accepted Answer

Occupant load is the floor area divided by the area-per-person factor in Table 3.1.17.1, for example 0.75 m2 per person for assembly space with non-fixed seats, 1.85 m2 for classrooms and 9.3 m2 for offices, or the actual number of fixed seats. Source: OBC Division B, Subsection 3.1.17..

Question 37

When must doors swing in the direction of exit travel in Ontario?

Accepted Answer

Egress doors must swing in the direction of travel when they serve a room or suite with an occupant load of more than 60 people, serve a high-hazard industrial occupancy, or open into an exit. Hardware must open easily without keys or special knowledge. Source: OBC Division B, Subsection 3.3.1..

Question 38

When does a room or suite need two egress doorways under the Ontario Building Code?

Accepted Answer

Two egress doorways are required where a room or suite has an occupant load over 60, exceeds the floor-area limits of Table 3.3.1.5, or where travel distance to the doorway exceeds tabulated limits, with the doorways spaced apart from each other. Source: OBC Division B, Article 3.3.1.5..

Question 39

How is travel distance measured within a floor area in Ontario?

Accepted Answer

Travel distance is measured along the actual walking path from the most remote point in a room or suite to the nearest egress doorway or exit, around fixed obstructions, not as a straight line, and it limits suite depth and layout flexibility. Source: OBC Division B, Subsection 3.3.1..

Question 40

What fire separations are required for hazardous rooms under the Ontario Building Code?

Accepted Answer

Rooms with elevated fire hazard, such as storage rooms with combustible material, repair garages, and rooms containing flammable liquids, must be separated from the rest of the floor area by rated fire separations, commonly 1 h or 2 h depending on the hazard. Source: OBC Division B, Subsection 3.3.1..

Question 41

What are the aisle requirements for assembly seating in Ontario?

Accepted Answer

Assembly occupancies with fixed or arranged seating must provide aisles sized for the occupant load, typically at least 1 100 mm where rows are served on both sides, with limits on row length, seat spacing and dead-end aisles, plus steps and handrails on sloped aisles. Source: OBC Division B, Subsection 3.3.2..

Question 42

What are the special egress rules for care occupancies under the Ontario Building Code?

Accepted Answer

Care, care and treatment, and detention occupancies require sprinklering, subdivided floor areas so occupants can be moved horizontally to an adjacent protected zone rather than evacuated downstairs, wider corridors and doorways for beds, and enhanced staff alarm features. Source: OBC Division B, Subsection 3.3.3..

Question 43

What are the egress requirements for residential suites under the Ontario Building Code?

Accepted Answer

Each dwelling unit needs egress to a public corridor or exterior, and where the suite spans levels or its egress path is exposed, a second means of escape may be required. Corridor travel from suite doors must reach exits in two directions in most layouts. Source: OBC Division B, Subsection 3.3.4..

Question 44

How is required exit width calculated under the Ontario Building Code?

Accepted Answer

Required exit width equals the occupant load multiplied by 6.1 mm per person for doorways, corridors and shallow ramps, or 9.2 mm per person for stairs, and never less than the fixed minimum widths, such as 1 100 mm for most exit stairs. Source: OBC Division B, Article 3.4.3.2..

Question 45

How many exits does a floor area need under the Ontario Building Code?

Accepted Answer

Most floor areas in Part 3 buildings need at least two independent exits. A single exit is permitted only for small, low-occupancy floor areas that satisfy strict limits on occupant load, area and travel distance. Source: OBC Division B, Subsection 3.4.2..

Question 46

How far apart must exits be located under the Ontario Building Code?

Accepted Answer

Where multiple exits are required they must be remote from each other, generally separated by at least one half of the maximum diagonal dimension of the floor area, though the required separation need not exceed 9 m in certain corridor-served layouts. Source: OBC Division B, Article 3.4.2.3..

Question 47

What is the maximum travel distance to an exit under the Ontario Building Code?

Accepted Answer

Typical limits are 30 m (about 98 ft) in unsprinklered floor areas, 40 m in most sprinklered floor areas, 45 m for certain sprinklered office, residential and low-hazard industrial floor areas, and 25 m for high-hazard industrial occupancies. Source: OBC Division B, Article 3.4.2.5..

Question 48

What are the required dimensions for exit stairs under the Ontario Building Code?

Accepted Answer

Exit stairs generally need at least 1 100 mm clear width, risers no more than 180 mm, runs at least 280 mm, landings as long as the stair width, about 2 050 mm headroom, and handrails at 865 mm to 1 070 mm height. Source: OBC Division B, Subsection 3.4.3..

Question 49

What are the exit sign requirements under the Ontario Building Code?

Accepted Answer

Exit doors in larger buildings must be marked by internally or externally illuminated signs using the green running-man pictogram, visible from the egress path, lit whenever the building is occupied, and supplemented by directional signs where the exit is not visible. Source: OBC Division B, Subsection 3.4.5..

Question 50

What fire separation is required around exits in Ontario?

Accepted Answer

Every exit must be separated from the rest of the building by fire separations with a fire-resistance rating at least equal to that required for the floor assemblies it serves, and not less than 45 minutes, commonly 1 h to 2 h in taller buildings. Source: OBC Division B, Subsection 3.4.4..

Question 51

What is a horizontal exit and when can it be used in Ontario?

Accepted Answer

A horizontal exit lets occupants pass through a firewall or rated fire separation into a safe area on the same level of an adjacent building or fire compartment. It may substitute for up to half the required exits, with refuge space of about 0.5 m2 per person. Source: OBC Division B, Subsection 3.4.1..

Question 52

When can exterior stairs be used as exits under the Ontario Building Code?

Accepted Answer

Exterior stairs can serve as required exits for lower buildings where they lead directly to ground level and are protected from fire exposure, meaning nearby windows and doors that could expose the stair must be limited or protected. Fire escapes are restricted to existing buildings. Source: OBC Division B, Subsection 3.4.6..

Question 53

Can an exit pass through a lobby under the Ontario Building Code?

Accepted Answer

Yes, but only one required exit may lead through a lobby, the lobby floor must be close to grade, travel through the lobby is limited to about 15 m, and the lobby must be separated and finished to restrict fire and combustible content. Source: OBC Division B, Article 3.4.4.2..

Question 54

What are the elevator requirements under the Ontario Building Code?

Accepted Answer

Under OBC Section 3.5, elevators must conform to CSA B44 (Safety Code for Elevators) and Ontario's elevating devices rules administered by the TSSA. The Code also governs hoistway fire separations, machine rooms and firefighter emergency operation. Source: OBC Division B, Section 3.5..

Question 55

Which buildings need an elevator under the Ontario Building Code?

Accepted Answer

The OBC rarely demands an elevator by name. In practice, barrier-free access rules in Section 3.8, stretcher access provisions, and the firefighters' elevator required in high buildings make elevators effectively mandatory in most multi-storey public, institutional and larger residential buildings. Source: OBC Division B, Subsection 3.8.2..

Question 56

When is a firefighters' elevator required in Ontario, and what must it include?

Accepted Answer

High buildings regulated by OBC Subsection 3.2.6 must have at least one elevator for firefighter use, with key-operated emergency recall and independent in-car operation, protected electrical services and emergency power, so crews can reach upper storeys quickly during a fire. Source: OBC Division B, Subsection 3.2.6..

Question 57

What are the escalator and moving walk requirements in the Ontario Building Code?

Accepted Answer

Escalators and moving walks must conform to CSA B44 and be licensed through the TSSA. They cannot count as required exits, the floor openings they create must be protected against fire and smoke spread, and adjacent guards must prevent falls. Source: OBC Division B, Section 3.5..

Question 58

What does the Ontario Building Code require for elevator machine rooms?

Accepted Answer

Elevator machine rooms must be separated from the rest of the building by fire separations coordinated with the hoistway enclosure, used only for elevator equipment, and provided with safe access, ventilation and temperature control appropriate to the machinery. Source: OBC Division B, Section 3.5..

Question 59

What are the code requirements for dumbwaiters and material lifts in Ontario?

Accepted Answer

Dumbwaiters and freight or material lifts are elevating devices: they must conform to the applicable CSA B44 requirements, be registered with the TSSA, and run in hoistways enclosed by fire separations under Subsection 3.6.3. Lifts carrying people follow different rules. Source: OBC Division B, Section 3.5..

Question 60

What fire separation is required for service rooms in Ontario?

Accepted Answer

Service rooms containing building service equipment generally require a fire separation with a fire-resistance rating of at least 1 h, with relaxations where the building is sprinklered or the equipment presents a low hazard. Doors must be rated and self-closing. Source: OBC Division B, Subsection 3.6.2..

Question 61

Where can fuel-fired appliances be located in a Part 3 building in Ontario?

Accepted Answer

Fuel-fired appliances generally must be located in a dedicated service room with a fire separation of at least 1 h, must not be placed in or under exits, and need combustion air and installation per CSA B149.1 or the applicable fuel code. Source: OBC Division B, Subsection 3.6.2..

Question 62

What does the Ontario Building Code require for electrical vaults and transformer rooms?

Accepted Answer

Electrical equipment vaults must be built as fire-rated service rooms free of unrelated services and storage, coordinated with the Ontario Electrical Safety Code, which adds construction, ventilation, drainage, door and clearance requirements, particularly for oil-filled transformer vaults. Source: OBC Division B, Subsection 3.6.2..

Question 63

What are the requirements for vertical service spaces and shafts in Ontario?

Accepted Answer

Shafts (vertical service spaces) must be enclosed in fire separations, generally rated to match the fire-resistance required for the floor assemblies they penetrate, with rated closures at openings and appropriate protection at the top and bottom of the shaft. Source: OBC Division B, Subsection 3.6.3..

Question 64

What are the incinerator room requirements in the Ontario Building Code?

Accepted Answer

Rooms containing incinerators require an enhanced fire separation, commonly 2 h, and are treated as high-hazard service rooms. Associated refuse chutes need dedicated protected shafts, sprinkler protection and properly separated intake and discharge rooms. Source: OBC Division B, Subsection 3.6.2..

Building Code FAQ

Ontario Building Code

British Columbia Building Code

Alberta Building Code

Québec Construction Code

National Building Code of Canada

Need an answer right now?